Installation

ENSURE THAT THE PRS-M30 IS OFF BEFORE ATTACHING AND/OR DISCONNECTING THE PRS-M30 FROM THE DJI M30/T.

Applicable Hardware

PRS-M30 Hardware Summary (Part 1)

PRS-M30 Hardware Summary (Part 2)

A	Left Shoulder Connecting Bracket - 3 Pieces (QTY 1)
B	Shoulder Screws - M2.5 x 16 mm (QTY 4)
C	Right Shoulder Connecting Bracket - 3 Pieces (QTY 1)
D	PRS Attachment Strap End Mounting Screws - M4 x 16 mm (QTY 2)
E	PSDK Anchoring Screw - M1.6 x 8 mm (QTY 1)
F	PRS-M30 Mounting Screws - M3 x 6 mm (QTY 4)
G	2.5 mm Hex Head Screwdriver
H	2.0 mm Allen Key
I	00 Phillips Head Screwdriver
J	Loctite 243 Thread Locker (QTY 2)
K	Strap Guide Bracket (QTY 1)

First Time Setup (Standalone Configuration)

This set of installation instructions applies only to customers who will only be using the PRS-M30 on a standalone DJI M30/T and will not be using the Dock 1. It is also for those customers who will be frequently removing their PRS-M30 from the DJI M30/T and subsequently re-attaching it. Refer to the first table below for the hardware applicable to this section and to the second table for setup instructions.

Applicable Hardware (First Time Setup - Standalone Configuration)

A	Left Shoulder Connecting Bracket - 3 Pieces (QTY 1)
B	Shoulder Screws - M2.5 x 16 mm (QTY 4)
C	Right Shoulder Connecting Bracket - 3 Pieces (QTY 1)
H	2.0 mm Allen Key

Step 1	Prepare to Mount the Strap Attachment Hardware	To install the strap attachment hardware onto the DJI M30/T drone you will need to remove the screws on both forward arms (QTY 4) that interface with the bracket, as shown (QTY2 on the right side, and QTY2 on the left side). Use the included 2.0 mm Allen Key.
Step 2	Install the Left Strap Hardware	Using the M2.5 x 16 mm shoulder screws (QTY 2) included in the PRS-M30 hardware kit, install the left shoulder connecting bracket on the left forward arm of the DJI M30/T, as shown. Use the included 2.0 mm Allen Key.
Step 3	Install the Right Strap Hardware	Repeat Step 2 to install the right shoulder connecting bracket on the right forward arm of the DJI M30/T, as shown.

Attaching the PRS-M30 to the DJI M30/T Drone (Standalone Configuration)

As before, refer to the first table below for the hardware applicable to this section, and to the second and third tables for setup instructions.

Applicable Hardware (Attaching PRS-M30 to DJI M30/T - Standalone Configuration)

D	PRS Attachment Strap End Mounting Screw - M4 x 16 mm (QTY 2)
E	PSDK Anchoring Screw - M1.6 x 8 mm (QTY 1)
F	PRS-M30 Mounting Screws - M3 x 6 mm (QTY 4)
G	2.5 mm Hex Head Screwdriver
I	00 Phillips Head Screwdriver
K	Strap Guide Bracket (QTY 1)

Step 1	Install Strap Guide Bracket On To Strap	Feed the strap through the grooves cut in the "Strap Guide Bracket", as shown. Take care that the strap is oriented properly (left and right indicated by lettering) and ensure not to twist the strap.
Step 2	Install Mounting Screws	Install the PRS-M30 using the included M3 x 6 mm mounting screws (QTY 4) and 2.5 mm Hex Head Screwdriver. The arrows indicate three of the (QTY 4) screw locations, with the fourth located behind the PRS-M30.

THE PRS-M30 MOUNTING SCREW HOLES ARE DESIGNED TO BREAK OFF DURING A DEPLOYMENT TO MINIMIZE THE DAMAGE DONE TO THE DRONE.

• ENSURE ALL QTY 4 SCREWS ARE SECURED PROPERLY WHEN INSTALLING THE PRS-M30.

• ENSURE ALL QTY 4 SCREWS ARE REMOVED FULLY BEFORE ATTEMPTING TO REMOVE THE PRS-M30.

Step 3	Insert Strap Mounting Screws Into Strap Ends	The PRS-M30 unit has an additional strap to secure the PRS to the DJI M30/T. Insert the M4 x 16 mm mounting screws for the strap ends (QTY 2) into the left and right strap ends respectively.
Step 4	Position Straps Around Forward Arms	Loop the PRS-M30/T straps around the forward arms of the DJI M30/T, as shown. The ends of the straps, as circled at right, will clip into a groove cut onto the carbon fiber shoulder brackets from the "First Time Setup".
Step 5	Tighten Connecting Screws Into Groove On Shoulder Brackets	Gently and slowly tighten the M4 x 16 (QTY 2) strap end mounting screws detailed in Step 2 (circled at right) to secure the PRS-M30 strap ends to the DJI M30/T shoulder brackets. Use the 2.5 mm Hex Head Screwdriver.
Step 6	Remove PSDK Port Cover and Anchoring Screw	Open the DJI M30/T's right side PSDK port. Remove both the port cover and the PSDK anchoring screw (circled at right in red). Use the included 00 Phillips Head Screwdriver for the screw.
Step 7	Plug in the PRS	Once the PSDK port and anchoring screw are removed, plug in the PRS-M30. Ensure the PRS cable is properly seated in the PSDK port before proceeding to step 8
Step 8	Insert PSDK Anchoring Screw	Insert the provided M1.6 x 8 mm PSDK anchoring screw (QTY 1) into the small hole at the bottom right of the PRS connector (circled at right) and carefully tighten to secure the connector. Use the included 00 Phillips Head Screwdriver.
Step 9	Power On Drone/PRS	To turn on the PRS-M30, you will need to turn on the DJI M30/T Drone.
Step 10	Check Continuity	Check for system continuity and errors on the DJI M30/T Transmitter. This will be indicated by the PSDK symbol on the right-hand side of the transmitter's screen when in the camera view.
Step 11	Power Off Drone/PRS	Power off the DJI M30/T. The PRS-M30 will take up to ten (10) seconds for the LED to turn off, once the LED is off the PRS is safe to approach. Do not unplug or move the M30/T or PRS-M30 until the PRS-M30 is turned off.

DURING REMOVAL, IT IS POSSIBLE THAT THE ASSOCIATED STRAP HARDWARE (QTY 2 M4 X 16 MM SCREWS) WILL BECOME STUCK IN THE STRAP ENDS. IF THIS OCCURS, EITHER CAREFULLY LOOSEN THE SCREWS FURTHER OR GENTLY MOVE THE STRAP FROM SIDE TO SIDE TO RELIEVE PRESSURE ON THE ENDS. DO NOT PULL EXCESSIVELY ON THE STRAP TO TRY AND FORCE IT OUT.

First Time Setup (Dock Configuration)

This set of installation instructions applies only to customers who will only be using the PRS-M30 on a DJI M30/T that is connected to a Dock 1. It is also for those customers who will be leaving their PRS-M30 permanently attached to the DJI M30/T without a need for removal. Refer to the first table below for the hardware applicable to this section and to the second table for setup instructions.

Applicable Hardware (First Time Setup - Dock Configuration)

A	Left Shoulder Connecting Bracket - 3 Pieces (QTY 1)
B	Shoulder Screws - M2.5 x 16 mm (QTY 4)
C	Right Shoulder Connecting Bracket - 3 Pieces (QTY 1)
H	2.0 mm Allen Key
J	Loctite 243 Thread Locker (QTY 1)

Step 1	Prepare to Mount the Strap Attachment Hardware	To install the strap attachment hardware onto the DJI M30/T drone you will need to remove the screws on both forward arms (QTY 4) that interface with the bracket, as shown (QTY2 on the right side, and QTY2 on the left side). Use the 2.0 mm Allen Key.
Step 2	Apply Loctite 243 to Shoulder Screws	Generously apply a layer of Loctite 243 to the threads of the M2.5 x 16 mm PRS shoulder screws to secure the screws to the DJI M30/T shoulder (detailed in the next step).
Step 3	Install the Left Strap Hardware	Using the M2.5 x 16 mm shoulder screws (QTY 2) included in the PRS-M30 hardware kit, install the left shoulder connecting bracket on the left forward arm of the DJI M30/T, as shown. Use the 2.0 mm Allen Key.
Step 4	Install the Right Strap Hardware	Repeat Step 2 to install the right shoulder connecting bracket on the right forward arm of the DJI M30/T, as shown.

Attaching the PRS-M30 to the DJI M30/T Drone (Dock Configuration)

As before, refer to the first table below for the hardware applicable to this section, and to the second and third tables for setup instructions.

Applicable Hardware (Attaching PRS-M30 to DJI M30/T - Dock Configuration)

D	PRS Attachment Strap End Mounting Screws - M4 x 16 mm (QTY 2)
E	PSDK Anchoring Screw - M1.6 x 8 mm (QTY 1)
F	PRS-M30 Mounting Screws - M3 x 6 mm (QTY 4)
G	2.5 mm Hex Head Screwdriver
I	00 Phillips Head Screwdriver
J	Loctite 243 Thread Locker (QTY 1)
K	Strap Guide Bracket (QTY 1)

Step 1	Apply Loctite 243 To DJI M30/T Mounting Screw Holes.	Generously apply a layer of Loctite 243 to the inside of the DJI M30/T mounting screw holes to help secure the PRS to the drone, as shown.
Step 2	Install Strap Guide Bracket On To Strap	Feed the strap through the grooves cut in the reinforcement bracket, as shown. Take care that the strap is oriented properly (left and right indicated by lettering) and ensure not to twist the strap.
Step 3	Install Mounting Screws	Install the PRS-M30 using the included M3 x 6 mm mounting screws (QTY 4) and Allen key. The arrows indicate three of the (QTY 4) screw locations, with the fourth located behind the PRS-M30. Use the 2.5 mm Hex Head Screwdriver.

THE PRS-M30 MOUNTING SCREW HOLES ARE DESIGNED TO BREAK OFF DURING A DEPLOYMENT TO MINIMIZE THE DAMAGE DONE TO THE DRONE.

• ENSURE ALL QTY 4 SCREWS ARE SECURED PROPERLY WHEN INSTALLING THE PRS-M30.

• ENSURE ALL QTY 4 SCREWS ARE REMOVED FULLY BEFORE ATTEMPTING TO REMOVE THE PRS-M30.

Step 4	Apply Loctite 243 to PRS Strap End Mounting Screws	Generously apply a layer of Loctite 243 to the threads of the M4 x 16 mm PRS strap end mounting screws (QTY 2) to secure the screws to the strap ends (detailed in the next step).
Step 5	Insert Strap Mounting Screws Into Strap Ends	The PRS-M30 unit has an additional strap to secure the PRS to the DJI M30/T. Insert the M4 x 16 mm mounting screws for the strap ends (QTY 2) into the left and right strap ends respectively.
Step 6	Position Straps Around Forward Arms	Loop the PRS-M30/T straps around the forward arms of the DJI M30/T, as shown. The ends of the straps, as circled at right, will clip into a groove cut onto the carbon fiber shoulder brackets from the "First Time Setup".
Step 7	Tighten Connecting Screws Into Groove On Shoulder Brackets	Gently and slowly tighten the M4 x 16 (QTY 2) strap end mounting screws detailed in Step 2 (circled at right) to secure the PRS-M30 strap ends to the DJI M30/T shoulder brackets. Use the 2.5 mm Hex Head Screwdriver.
Step 8	Remove DJI M30/T right side PSDK port cover and anchoring screw.	Open the DJI M30/T's right side PSDK port. Remove both the port cover and the PSDK anchoring screw (circled at right in red). Use the 00 Phillips Head Screwdriver for the screw.
Step 9	Apply Loctite 243 to PSDK anchoring screw connecting hole.	Generously apply a layer of Loctite 243 to the inside of the PSDK anchoring screw connector hole to secure the PRS to the drone, as shown.
Step 10	Plug in the PRS.	Once Loctite 243 has been applied to the inside of the PSDK anchoring screw connector hole, plug in the PRS-M30. Ensure the PRS cable is properly seated in the PSDK port before proceeding to step 11.
Step 11	Insert PSDK Anchoring Screws	Insert the M1.6 x 8 mm PSDK anchoring screw (QTY 1) into the small hole at the bottom right of the PRS connector (circled at right) and carefully tighten to secure the connector. Use the 00 Phillips Head Screwdriver.
Step 12	Power On Drone/PRS	To turn on the PRS-M30, you will need to turn on the DJI M30/T Drone.
Step 13	Check Continuity	Check for system continuity and errors on the DJI M30/T Transmitter. This will be indicated by the PSDK symbol on the right-hand side of the transmitter's screen when in the camera view.
Step 14	Power Off Drone/PRS	Power off the DJI M30/T. The PRS-M30 will take up to ten (10) seconds for the LED to turn off, once the LED is off the PRS is safe to approach. Do not unplug or move the M30/T or PRS-M30 until the PRS-M30 is turned off.

DURING REMOVAL, IT IS POSSIBLE THAT THE ASSOCIATED STRAP HARDWARE (QTY 2 M4 X 16 MM SCREWS) WILL BECOME STUCK IN THE STRAP ENDS. IF THIS OCCURS, EITHER CAREFULLY LOOSEN THE SCREWS FURTHER OR GENTLY MOVE THE STRAP FROM SIDE TO SIDE TO RELIEVE PRESSURE ON THE ENDS. DO NOT PULL EXCESSIVELY ON THE STRAP TO TRY AND FORCE IT OUT.